[1] 张云启.深海活塞式压力平衡装置密封结构的研究[D].合肥工业大学，2014. [2]Zhang Yunqi.The Research on Seal of Piston Pressure Balance Device in Deep Sea[D]. Hefei University of Technology, 2014. [3] 杨斐琦, 水下滑翔器的结构设计与分析[D].青岛科技大学，2014. [4]Yang feiqi.Design and Analysis of the Structure of the Underwater Glider[D]. Qingdao University of Science & Technology, 2014. [5]段密克，王科社，黄喜淦等.形圈配合挡圈动密封的有限元分析[J].北京信息科技大学学报, 2018, 33(2):82-85 [6]Duan mike, Wang keshe, Huang xiganetal.Finite element analysis of the dynamic sealing characteristics for O-ring with retainer ring[J].Journal of Beijing Information Science ＆ Technology University, 2018, 33(2):82-85 [7]饶建华，陆兆鹏.形橡胶密封圈配合挡圈密封的应力与接触压力有限元分析[J].润滑与密封, 2009, 34(5):65-68 [8]Raojianhua, Lu zhaopeng.Finite Element Analysis of Stress and Contact Pressure of Rubber O-sealing Ring with Back-up Ring[J].Lubrication Engineering, 2009, 34(5):65-68 [9]周志鸿，章康雷，李静等.形橡胶密封圈应力与接触压力的有限元分析[J].润滑与密封, 2008, 31(4):86-89 [10]Zhou zhihong, Zhang kanglei, Li jingetal.Finite Element Analysis of Stress and Contact Pressure on the Rubber Sealing O-ring[J].Lubrication Engineering, 2008, 31(4):86-89 [11]王伟，赵树高.应力松弛下橡胶 形密封圈的有限元分析[J].润滑与密封, 2008, 33(10):24-26 [12]Wang we, Zhao shugao.Finite Element Analysis of Rubber O-ring Seal with Stress Relaxation[J].Lubrication Engineering, 2008, 33(10):24-26 [13]赵文德，宿德春．.水下机器人耐压壳体O 型圈密封性能有限元分析[J].机械工程师, 2009, 1(7):66-68 [14]Zhao wende, Su dechun.Finite Element Analysis of the Sealing Performance of O-ring in Pressure Shell for AUVs [J].Mechanical Engineer, 2009, 1(7):66-68 [15]陈家兑，谢庆生，王自勤等.液压式配气系统形密封圈动密封特性分析[J].润滑与密封, 2014, 39(11):90-92 [16]Chen jiadui, Xieqingshen, Wang ziqinetal.Analysis of Dynamic Sealing Characteristics of O-ring in Hydraulic Valve System[J].Lubrication Engineering, 2014, 39(11):90-92 [17]谭晶，杨卫民，丁玉梅.橡胶密封圈密封性能的有限元分析[J].润滑与密封, 2006, 31(9):65-69 [18]Tan jing, Yang weimin, ding yumei.Finite Element Analysis of the Sealing Performance of O-ring Seal Structure[J].Lubrication Engineering, 2006, 31(9):65-69 [19]王国志，张毅，刘桓龙等.深海环境下的形圈静密封设计[J].润滑与密封, 2014, 39(10):88-91 [20]Wang guozhi, Zhang yi, Liu huanlong, etc.Design of O-ring Static Seal Structure under Deep-sea Environment[J].Lubrication Engineering, 2014, 39(10):88-91 [21]王国志，刘桓龙，刘晟昊.表面粗糙度对水压元件 形圈静密封性能的影响[J].润滑与密封, 2013, 38(5):87-90 [22]Wang guozhi, Liu huanlong, Liu shenghao.Effect of Water Hydraulic Component Surface Roughness on Static Sealing Property of O-ring[J].Lubrication Engineering, 2013, 38(5):87-90 [23] 徐同江.基于Ansys的O形密封圈的有限元分析[D]. 山东大学，2012. [24]Xutongjiang.Xieyujun.Ansys Analysis of the Sealing Performance of O-Sealing Ring [D].Shandong University, 2012. [25]王杰，谢禹钧.关于橡胶形密封圈的分析[J].辽宁石油化工大学学报, 2008, 28(4):48-50 [26]Wang jie. Ansys Analysis of Rubber O- Sealing Ring[J].Journal of Liaoning University of Petroleum & Chemical Technology, 2008, 28(4):48-50 [27] 杨春明，谢禹钧.基于Ansys的橡胶O形密封圈的密封性能有限元分析[J].弹性体, 2010, 20(3):49-52 [28]Yang chunming, Xieyujun.Ansys analysis of the sealing performance of rubber O-sealing ring[J].ELASTOMERICS, 2010, 20(3):49-52 [29] 贺庆平，张付英，沈晓斌.基于有限元分析的液压往复密封优化设计[J].机械设计, 2007, 1(7):6-8 [30]He qingping, Zhang fuying, Shenxiaobin.Optimization of sealing O-ring based on finite element analysis[J].Machinery Design & Manufacture, 2007, 1(7):6-8
